Optoma dlp projector troubleshooting. OPTOMA 1080P DLP USER MANUAL Pdf Download.

Support

Optoma dlp projector troubleshooting

Hi Ken, The lamp may have been damaged when you removed it to clean it. Problem 2: My projector is getting too hot after replacing the lamp Solution: Clean your air filters and ventilation holes. The first thing I did when I got home was download a manual and look up how to determine the hours it had been used. Game Display Mode provides a visual advantage by boosting shadows and dark scenes for greater visibility of impending obstacles. Pay a visit to the e, and you'll see that the company has no shortage of 720p and 1080p projectors targeted at this audience. Optoma makes a full range of projectors.

Nächster

Support

Optoma dlp projector troubleshooting

Problem 6: The screen color is wrong and the picture is flickering. The message will appear 30 hours before suggested replacement of lamp. To reach the ribbon, the cover needs to be removed. Overscan the image to remove video encoding noise on the edge of video source. Proper alignment and setup is another challenge that must be addressed with projector use. Mate this model with a value-oriented ambient-light-rejecting screen perhaps the that I recently reviewed , and you should get excellent results for daytime sports watching or other high-ambient-light viewing situations. Projector Problem 10 — Projector Lamp door switch broken This is quite a minor problem to resolve.

Nächster

OPTOMA 1080P DLP USER MANUAL Pdf Download.

Optoma dlp projector troubleshooting

What is wrong with the machine? Hi Mark, First thing to check is the lamp timer that is has been reset to zero. It could also be alignment issues but I doubt that since you did get that blue bar. What am I doing wrong or what can I do from here to get the new lamp to work and project on the screen? Try contacting Epson and discussing the repair for the replacement part with them. Another issue might be the rpm sensor in that fan is bad. Always reset your lamp timer after replacing the lamp. This problem usually only happens when you have replaced only the bulb and not the entire housing. I opened it up to see if anything was loose, but everything looks okay.

Nächster

Support

Optoma dlp projector troubleshooting

Still no splash screen or image. Hi Jamm, First check the air filters and make sure they are free of dust and debris so that air can circulate properly. The lamp starts no image and after 10 sec you can see the image flashing and then the lamp goes off. I have a question I recently replaced my lamp in my viewsonic projector. A broken fan will cause the device to overheat quickly and could cause lens or bulb damage to the device, which is very expensive to replace. As a school we have many overhead projectors and regularly replacing the lamps. I bought a new lamp and the light is still on.

Nächster

How to Troubleshoot a BenQ Projector

Optoma dlp projector troubleshooting

Simply choose the brand of your {product} in the menu to find your manual. It needs to be reset or the warning lights will continue to flash. If you bought from a recognized dealer, then you may have a defective lamp. A black screen usually means that the projector is not accepting the lamp connections. Hi Erald, Yes, you can replace the color wheel. I have pulled this thing apart, cleaned all the fans etc still with the same result. All of a sudden after running the projector for about two minutes, the color becomes blue-ish, then dims, and the unit immediately shuts down and shows the temp light flashing.

Nächster

Manual

Optoma dlp projector troubleshooting

It could also be your power source but usually these ghost images and color issues are the ballast and color wheel. Try replacing the bulb as that is much less expensive than replacing the colour wheel. Hi Eldon, How is the picture not working? I cant even pull up the menu settings or anything. What brand and model of projector do you have? As I mentioned earlier, there's no noise reduction, but I didn't feel it was needed, since the picture generally looked smooth and clean. Plugged in power cable then when I pressed the power switch to on, it went pop and now has no power. A friend has an Epson projector which was working. That sounds like your fan is not working.

Nächster